Oshlun SBNF-100100 10-Inch 100 Tooth TCG Saw Blade with 5/8-Inch Arbor for Aluminum and Non Ferrous Metals

Reliabile and good quality.

I mounted this on my recipricale saw and use it primarily for cutting 6061 aluminum extrusion. It works equally well on small 1X1" angle and also on larger 2X3" extrusion and cuts through it with ease. No lubricant/wax or other helper is needed on the cuts and the saw tracked just as cleanly as if it was cutting through wood What I like about this blade is the fact that it does not want to kick the part up or grab into the material so clampingon the part was only neceessary on one side. The surface finish of the cut was very similar to a semi finishing machining cut and required very minimal clean up of burrs, an added +. I have cut several hundred peices and there is no noticable depreciation or wear on the teeth and it works just as well as the first time I used it. Would recommend this for anyone needing to make quick work on aluminum cutting. Price wise this blade performed as well or better than my now retired Freud Diablo blade which cost me about $85 originally. Great value for the money and you won't find a comperable blade for less.

Just received this blade yesterday, and I put it to work cutting 45 deg angles to make Aluminum Window Screen frames. This blade is sturdy and strong, no wobbling on my cheap Delta Miter saw, and it cut through the aluminum frame like cutting through cheese. I did use a little bit of lub, i.e. WD-40, as the directions on the carton stated, but I do not think that I needed to do so. Prior to purchasing this blade, I had used the abrasive style blade to cut through the aluminum frame and the cut quality was a disaster, and not the quality that I will install on the front of my house. So I looked up the various blades that were available for cutting aluminum, and I found this one with great reviews. I went ahead and purchased it to try it out. Great value and great performance. Although there is another Oshlun blade available to cut aluminum with 60 teeth, but I opted to buy the 100 teeth blade which makes it much easier to cut through aluminum, and the blade will last a lot longer. I am glad I bought it.

I need to cut aluminum frequently but also hate changing blades on my miter saw because it takes 35 minutes to remove all the safety gizmos before spending 10 seconds changing the blade. Using the wrong blade on a 10" saw can be VERY dangerous, and some blades made for metal pretty much burn their way through wood. With this blade, I get great cuts on aluminum, as expected. I can also cut most other materials just as clean as with other blades, just slightly slower. I'd much rather cut a piece of wood in two seconds instead of one second rather than changing blades twice.Metal blades can be very specific, even if they look basically the same. Don't use this for steel. I have one of their steel blades, and it's also good. Similarly, if you need to cut stainless steel, buy a blade for that. It might seem like a lot of trouble and money to have so many blades, but they exist for a reason. If you're not a pro, a good blade will likely last a lifetime, or at least until you buy that CO2 laser you've always wanted.

Worked well for cutting aluminum picture frames. Just left tiny bit of rough edge at the back of the cut. Not quite as good for polymer picture frames. Melts the back edge more than specialty plastic cutting blade

Worked fine in a miter saw; well balanced and straight. Makes nice clean beautiful cuts on 6061 Aluminum extrusions. It also cleans ends of stock by just barely skimming a roughly cut end; go slowly and the end comes out nice and smooth needing only a light deburring.

Wow... just, wow! I needed a way to cut aluminum angle stock with my table saw for a project I was working on, and this blade was the best option that I could find. Given the relatively low price, I wasn't sure what level of quality I could expect, but I really couldn't justify buying a more expensive blade for a single project. Fortunately, I didn't have to. When I tried it on a piece of scrap aluminum stock, the cut was excellent - smooth and clean, with very minimal burring. Even better, the blade cut through the light aluminum bar without any effort or binding. Nice! I cut the angle stock for my project and then found that with a blade that can cut soft metal so well, I had other projects that were suddenly practical. I've used the blade on aluminum, soft brass and hardwood so far, all with excellent results. This blade isn't inexpensive, but it's a bargain at the price if you need to cut softer metals and/or to make nice, smooth cuts on hardwood planks.

I was looking for a bade to cut aluminum for a FIRST robotics team working out of my basement. My initial search through a well known industrial supplier showed blades like this starting at $250. That was pretty much a non-starter. I found this one on Amazon and read the reviews and decided to give it a try. It cuts cleanly, quietly, and quickly. We have been cutting parts for several weeks now and the blade shows no signs of dulling. It also works great on PVC pipe and wood (we used that for training purposes. I have done a lot of shop work over the years and I can say this is an excellent blade. I highly recommend this to anyone who is planning to cut aluminum on conventional shop equipment. I used this blade on a table saw.

This is a fantastic saw for cutting non-ferrous metals. High tooth count gives a nice clean cut. The attached image is my first cut with the saw blade on 76mm X 6mm aluminium.Unlike so many other saw blades I have looked at, this one will work at a RPM of a standard mitre saw. I was afraid after watching many YouTube videos of people modifying their saws to work with metal cutting saw blades. I will be able to use this blade on my table saw as well.My only complaint is that when the saw blade is installed, the markings for the blade and direction are on the opposite side of my saw. A marker, to just confirm rotation direction was all I needed.

This blade has been giving me super clean cuts in aluminum extrusion on a mitre saw. Also very clean crosscuts in a radial arm saw (so far just in wood, might try an aluminum plate on there next).

Great saw blade for thin aluminum. I use it for fabricating window screens. When occasionally used with a wax stick, it is sure to last a long time. So far, so good.

Used to cut a shower door header and cut through it like butter and left a very smooth finish and clean angles. 60 tooth 10 inch version. First time using an aluminum cutting blade so not sure how it compares to others but really satisfied with this.

Va bien a date l avenir nous le diras